© COPYRIGHT / SERVICE MARK / TRADEMARK NOTICE:  by our "ShrimpNFish™" Family…  Copyright 2013 ShrimpNFishFlorida™, FishNShrimpFlorida™, by Gator Management Services.™, Nautical Gator, LLC..™ A People Company! All Servicemarks, Trademarks, Slogans, ©Copyright's, names, photo's, artwork, logo’s & trademarks are the property of our "ShrimpNFish™" Family... All artwork was designed for ShrimpNFishFlorida™. And may not be reproduced in any manner whatsoever... for more info on Copyright Servicemarks, Trademarks, and terms of site usage. click here! [All Rights Reserved ].

Solder Gun / Iron

Solder and flux

Zip ties

Heat Shrink Butt Connectors

Drill Press

Thick Rope

Line Clip

12 volt Plug, 12 Volt Cigarette lighter Plug, Battery Clips, or Hard Wire Battery Clip

(As Shown in Photos)

Schedule 40 PVC PVC  NPT Bushing (As shown in Photo)

1/2 NPT strain relief connectors, rubber Washers, Plastic Nuts

battery alligator clips

Make sure you solder your wiring and do not Butt Connect them, mainly because Butt connectors can malfunction and create a short and your lights will go out...

When you solder them together this cannot happen and your lights will be reliable for years...

Putting LED Shrimp Light Together

Cut your outer Clear Tubing to size...

Cut your inner PVC Pipe to size...

Drill hole for wiring...

Test fit all components...

Clean off inside PVC Pipe with either acetone or alcohol...

In this photo you can see the hole I drilled for the LED wiring to go through...

Using a Dremel tool...

Now using gloves peal the 3M off of the back of the LED Strip, ONLY a Little at a time... Making sure it does not get contaminated with dust...

Then wrap the LED Light Strip around the inside PVC Pipe...

The LED Light Should look like this...

Install the two end rings to the inside pipe, so the inside pipe has a snug fit too the inside of the end caps, so the lights wrapped around the pipe does not rattle...

OK, ready for testing your light, before you solder the wiring together... and place heat shrink around the wiring...

I use a rubber mallet to tap on the end caps for a flush fit...

OK, this is important:

Notice that there is a slight space on each side of the LED Light Strip....

This is not a mistake, or mismeasurement ... It was done on purpose...

if you make the lights to short they will not have the proper buoyancy....

Note: The lights need to float under the water, so you can adjust the float level.... so the lights need to be buoyant...

Your finished light should look something like the below...

This Shrimp Light Build has 150 GREEN LED Lights

Come Join The Fun

On our forum I will show you step by step

ALL Lights and Supplies can be bought from GatorTough Shrimp Lights at http://www.gatortough.com/

DIY Shrimping Lights - How to make your own Shrimping Lights

This is how to Make LED Shrimp Lights, Shrimping Lights DIY (Do It Yourself) Shrimp LED Light Build..

Hi I am going to show you how you can make your own LED Shrimping Lights…

It’s no secret; you can make the same type of LED shrimping lights as you can buy on the market…

This information is something that you won't see the manufactures posting...

But I will be making it available to all our DIY (Do It Yourself) members...

that are interested in making your own either as a hobby or to save yourself some money!!!

I found that the green "SMD 5050 LED’s Tri Chip" Strips, provide more lumens than the SMD 3528 led strips.

First you will need to order the parts needed to start your build…

PARTS LIST:

Shrimp Light Supplies Needed to Build your DIY Shrimp Lights…

LED Green light strips (High Lumens)

40 ft SJOOW 2W 16/2 Bulk Cable

Liquid Tight Cordgrips

Schedule 40 PVC White End Caps

Schedule 40 PVC Clear Pipe

Schedule 40 PVC PVC Bushings

Schedule 40 PVC NPT Bushings

Schedule 40 PVC White Pipe

Schedule 40 PVC Couplings

3m 5200, PVC bonding agent cement. Or Pipe glue and cleaner primer...

Heat Shrink wrap

Soldering gun

Solder and flux

Thick Rope

Line Clip

12 volt Plug, 12 Volt Cigarette lighter Plug, Battery Clips, or Hard Wire Battery Clip

Zip ties

NOTE: If using Flat End Caps, you do not need the Bushings or Couplings, instead you drill a hole and just screw in your Liquid Tight Cordgrip with a seal and nut, adding a drop of 5200 to the under side... (just for added protection)

The hole needs to be drilled with a drill press!!! Drilling by hand will not be accurate enough to except the Liquid Tight Cordgrip...

To find a suppliers just visit our forum and email me.

Shrimp Light Supplies Parts List and Photos

LED Green light strips (High Lumens)

You can buy these LED Light Strips from GatorTough Shrimp Lights HERE!

40 ft SJOOW 2W 16/2 Bulk Cable

Schedule 40 PVC White End Caps

OR

 PVC Flat Cap

NOTE: If using Flat End Caps, you do not need the Bushings or Couplings, instead you drill a hole and just screw in your Liquid Tight Cordgrip with a seal and nut, adding a drop of 5200 to the under side... (just for added protection)

The hole needs to be drilled with a drill press!!! Drilling by hand will not be accurate enough to except the Liquid Tight Cordgrip...

Liquid Tight Cordgrips

Schedule 40 PVC Clear Pipe

Schedule 40 PVC White Pipe

Schedule 40 PVC Couplings

3m 5200

Pipe glue and cleaner primer...

Heat Shrink wrap

How to Make LED Shrimp Lights.

DIY (Do It Yourself) Shrimp LED Light Build..

I will show you step by step

Here is an overview on how to build your own Shrimping lights